Plumbing Basics: What You Need for Bathtub Installation
Plumbing Basics: What You Need for Bathtub Installation
Blog Article
They are making a number of great pointers on How to Install a Bathtub Yourself in general in this great article further down.
Setting up a tub isn't precisely brain surgery, yet it does call for strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bathtub with a new one is additionally a reasonably hard project. If the old bathtub is readily accessible, the job can relocate immediately; if you have to open up a wall surface to eliminate the old bathtub as well as place the brand-new tub, the task is a lot harder. In either situation, the job is within a house handyman's abilities, although you will certainly need a helper to vacate the old bathtub as well as set in the brand-new one. See to it you have qualified yourself for the work as well as are comfortable trying it. As opposed to hiring a specialist to take over a halfway-completed task, it is far better to take into consideration utilizing one before you start. Possibilities are you might need a specialist plumber to make tube connections.
This post will certainly assist you install a new tub in your shower room if you have actually currently gotten a brand-new bathtub and do not need to transform the setup of your previous water pipelines.
Your tools and also product checklist should comprise the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, switch on the taps to drain pipes any water remaining in the system. The process of eliminating the existing faucets can be fairly troublesome as a result of the limited access that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a cloth all set for the staying water that will certainly come from the pipelines. As soon as the supply pipes have been eliminated, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming during this process. When the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in location between the faucet and also the sink. Secure the faucet in position with the producer given backnut. As soon as the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous kind needs to be attached to the tap finishes first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Using the two wood boards under its feet, position the tub in the needed setting. The wood boards are helpful in equally spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four small points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the level and adjusting the feet on the tub till the spirit level reads degree.
To install faucets, fit all-time low of the outermost flexible tap port to the appropriate supply pipe by making a compression join; then do the exact same for the other faucet.
Switch on the water system and also examine all joints and also brand-new pipework for leakages and also tighten them if needed. Load the tub and likewise inspect the overflow electrical outlet and also the normal electrical outlet for leakages.
Finally, take care of the bath paneling as defined in the producer's user's manual. Tiling and also securing around the bath tub needs to wait up until the tub has actually been used a minimum of when as this will certainly settle it right into its last setting.
Getting ready for the Installment
First of all, the supporting framework supplied with the bathroom must be fitted (if needed) according to the maker's instructions. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets system to stop stress on the bathtub.
Fit the versatile faucet ports to the bottom of both faucets utilizing 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you make use of every one of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its last position.
Tiling Around the Tub
In the area where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to break a stiff seal, creating the water to pass through the wall between the bath and the tiling, causing problems with dampness and possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components and fittings. They are sold in tubes and also cartridges, and can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always load the tub with water before securing, to allow for the activity experienced when the tub is in usage. The sealant can break fairly very early if you do not think about this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly available on the marketplace. It is suggested to fit the tiles making use of water-resistant or water-proof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was shown that write-up about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from someone on a different web address. Sharing is good. Helping people is fun. We thank you for reading our article about How to Install a Bathtub Yourself.
High-quality emergency response guaranteed. Report this page